For the BMW G650 X Bikes(applies to all the BMW G650 Xcountry – XChallenge – XMoto) – There is always a possibility for you to swap the rear wheel diameter size between 17″ or 18″ rear wheel selection.
The computer does the calculations itself with the rotations or the speedo adjustments based on the size that is already fed into the computer. It is always a good idea to be able to have the right readings while I personally do not have an accurate measurements of how much difference do they read between each selection.
The process to swap the sizes is a little more than tricky as you need to hold the button and to adjust the battery connection at same time. Tip: Easier if someone else can help you as well to hold the battery.
Instructions: This is how to change wheel size:
Remove ignition key from lock and disconnect battery.
Press the Set-button and connect the battery.
Don’t let go of the Set-button until i’ll tell you so!
The software version is shown on the display.
Don’t let go of the Set-button until i’ll tell you so!
The display counts down from 15 to 0.
When the countdown completes the parameters of the wheels are displayed, one after another.
Now you can let go of the Set-button.
When the wheel-size you want (diameter where speed is usually and circumference below where odometer is normally found) appear on the display, press the Mode-button.
That’ll save the new wheel size in memory.
Disconnect and then reconnect battery (don’t know if it’s necessary but that’s how I do it and it works).
Swapping 18″to17″ OR 17″to 18″
I will add-in the pictures once I do the swap between the two different sets of wheels and makes life easier to do the things at the same time in above sequence.
Hope this will help you get to choose your right wheel display settings too.
The so called XC, the story that shifted me in dimensions has now left and it is the time to warm up to something new for the next level. Not that I know much about it yet but shall know in the times to come.
My beloved G650 XCountry has been dispatched to the new owner and my next lady the G650 XCountry is in the making.
It was a hard decision to part away from one to let the next one come in. Never thought this would be the case that I would let this go but due to the fact that LB07 has left the marks that needs to let me build myself all again. I hate to say but sometimes the memories haunt you that you spend so much time with your objects to create moments with them and then you have to part away. Atleast our objects are better than the most human relationships.
All is well and good, in the world as long as I keep riding. Sometimes I just ride to get rid of what was in the past, like a roadsign that you just crossed and it only deserved to be spotted once and never to be seen again.
I was after a 21″ front and that is where it all began… where it ended – well, that is an unsaid story for now but like my dearest friend Wolf says – rider of the dark cloud*, must live in the dark. So I tried to get rid of one dark cloud to enter into another one.
Transitions from one XCo to the next XCo would take me some getting used, for I have to understand a lots of unknowns, yet to make a bond and then finally get myself in the grips of it under my bum. I welcome you shortly to the next level of where this life goes, MarlenkaZ is coming or call it DarkCloud2.
Often the simple things as stated by BMW which makes them really simple are not as simple if:
#1. You do not have previous experience (Novice or little experience)
#2. All the tools [BMW are really shit and kinky about their own tools and sizing(unique)]
#3. Creative mindset to get around them or forget about it.
Surely, that there are endless blogs available on how-to but this one is for my own keep and anyone else who is to do this for the first time or repeat looking at nitty gritty.
My G650 XCo was acquired some 5years back and since then barely much was ever done, but was ridden for a good while and about 15000kms in between those 5 years until now.
Previous owner history, was through the service book as it seems all BMW services done were on intervals but something not quite right. Perhaps the bike has been sat too long between its active usage. I will write down the other issues as encountered in a another thread.
This was not purely an activity for Spark Plugs change but more to do with Cam Tensioner change, that is covered here in this blog. I decided to keep a track of this for only spark plugs replacement.
So to start with as little and as much, please note that following tools are needed:
18mm Spark plug socket (I somehow believed it was in my kit, but wasn’t) – check yours + a long deep arm to reach the Spark plugs. [Alternative to buy or an another cheaper option would be this]
Special R-ring breaker tool (I hate those BMW hose clamps, extremely unpractical, so get them to normal screw driver hose clamps, found everywhere in a hardware shop). Take a note that once these clamps have been removed, you cannot re-use them. These R-rings are an extremely stupid idea by BMW!
Coil Remover (I did not have this tool, but used a normal adjustable wrench for a coil undoing. You can order one from here or use the way I used the wrench to pull it out.
Main stand or getting bike to be stable while you work on, is not a necessity but an extreme help. So anything would do that holds it in place.
Access to the Spark Plugs:
Remove the plastic panels on the left, right, center [This is an easier bit, with an hex key, should be [10mins], you need smaller hex key to remove the front two top hex nuts on top of the radiator, holding the main plastic component] – In total, 8 bigger hex nuts, and 2 smaller hex nuts. (one of the small hex nuts, can be left in main tank tank part holding the small plastic part – the one above the radiator, loosen it up to just slide out easily.)
Removing the Battery. [About 5mins, careful if your battery is stuck and need extra force, ensure the bike is well in its position] Remove from the terminal connections. You need to remove the battery as it sits in the air box chamber basket.
Undoing the air temperature connector sensor wire on the let side.[2mins] You may need a nose plier to pull that clip out on the sensor and then it just slides out easily. Pull out the complete metal clip.
Remove the relays mounted on the rubber mounts hanging from the airbox[2mins]. Easily done.
Breather hose [5mins] . Additionally, when removing it may not be possible to keep the breather hose in its place and harder to get it back in easily. I cut the cable ties on this breather hose and removed it from the right bottom front corner. Easier to let it slide down next time when redoing to reverse the process.
Remove the air box chamber [About 10mins, two hex nuts on the main front fork frame and two on the base near the seat] Note: The front two nuts are different sizes, good to know from the beginning so you won’t hassle up like me in the end.
Lifting up the complete airbox that connects to throttle body[2-3mins]. There was little struggle to pull it apart but is normal as long as all else has been followed above.
This now gives you a clear view of the top of the cylinder.
Note the positioning of the Spark plugs, this is where from all previous posts and forums I gathered this has to be in very specific position but I don’t see how or why it would make a difference. The coils are same inside and the positioning is rather to ensure that wires are in right place. Note: The black coil is to the inner side of the engine and the grey one on the outer towards the frame.
Pulling out the coils, BMW reprom says, use special tool(as mentioned above) but after trying to be careful and without a tool, it was rather the case, of carefully pulling out the coils with the adjustable wrench
User an extra cloth in the mouth holding the top of the coil to ensure this is not too hard but was fine to get the coils pulled out.
You now have the full view of the spark plugs accessibility. Should be easier and simple but take a note of the tools and alternatives as may not always be the case, you have them all.
It so happens that my friend who offered me all his tools and garage, didn’t have an 18mm socket so it was going not so well, but then there was somewhere in the old heap of tools, he found a worn out 18mm which required an extra work but now, I know I have to buy a 18mm spark plug socket. Just a self note!
Coming to finally, the spark plugs.
I got the Iridium spark plugs to replace the old NGK one. It was in a pretty bad shape as the previous owner possibly didn’t take care of it or they seemingly have never been replaced before (I would say so looking at them)!!
You need to have a long enough arm on your socket to get down to the spark plugs. Just a caution if you have old traditional 18mm, it may not be enough on its own without a long arm going down.
Another pointer that surprised me was that the new NGK Iridium plugs didn’t have that round metal cap on its end but threads. So I was glad that my friend had them on his other spare spark plugs, these caps but I am suprised these ones didn’t come with these caps and my old spark plug was a fixed one, that means, when the old cap was tried to be removed, it break the whole long metal inside and these are not replaceable from all old spark plugs if you don’t have them.
Better to be aware than to be sorry when working on this “Simple” task! not that as I thought it looked in the Reprom, hey 10mins jobby, no please do not count on what the reprom tells, it looks very simple but NOT!!
Once you have had everything out, this would be a reverse process on its own to get back everything in order.
In my case, I was going for two more additional items, first one being easier to do – cleaning up idle actuator, while the other one, cam tensioner replacement was going to be fun! You can follow my next write up on that one.
Additional reference: Spark plugs – I found a cheaper discount going on spark plugs, so I was of the notion to buy an extra pair right now. So, I had to check if I can just buy and keep them for future use. I found out this is fairly possible to keep the spark plugs and they will remain the way they are without any issues. Feel free to store them in a dry place, if you may be wondering this works good. Yes, they have long storage life when stored in a dry place and the needle is kept secured, best to leave them in the original packaging.
Tightening torques 0164 – G 650 Xcountry
12 12 011 Renewing all spark plugs +12 12 513
Spark plugs Tightening torque Value 23 Nm
World over, this is a given fact what makes you feel good, may not work for someone else unless it takes off that stress which is either taken off by drugs, sex or coffee but in certain cases, there is a therapy above all of this that calls for nothing but just you and yourself to experience its magic.
Nothing they say makes you feel better unless it is the fresh air, in this case really fresh and something that makes your blood roar, roar like it never has before, to kick your Adrenalin running.
Well, no this is a different kind of a “Therapy” – it is known as motorcycling and IF it is not in your blood, I warn you do not do it – It is not a seasonal exotic luxury that most people here in Europe treat it as, this is where I repeat – it is not for everyone.
Sometimes in life, you do things that makes you feel connected to who you are and it is in your blood, not in your show off fancy expensive motorcycle or in your Adventure embedded clothes and stickers on the motorcycle… I do not belong to your category of Adventures or being called stupid because this is what you do not have or will never have in you because you were not born with it!!
Adrenalin rush included with endorphins released as I push to extremes knowing that I have that throttle in my right hand and I forget about everything else, this is where I leave everything else behind, my past, my present and I only see what is in front of me – letting me release my demons with a fear that one single mistake and I will be in the gutter! (or worse, yes I have been there too- broke a shoulder but came out alive).
This is my therapy session, in real wonderful below zero°C temperature and the windchill that cleanses everything else that holds me fearless. (As I said, with a warning, this therapy is not for you if you do not know how to) – The threshold is those three digits that counts which kicks in fast but knowing my limits.. I am my own man.
I say no more, those words are mine and for me only… You enjoy the pictures and feel whatever else you want to feel other than my words. These words may not mean anything to you.
The session is done for today, once I found myself.. and told myself … everything that only matters to me… the soul listens!!